Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 112 / 192

CS2610

M46O515A

(1) lower link

6. The lowering speed of the lower

link is proportional to the applied

weight but can be controlled by ad-

justing the draining passage of the

hydraulic fluid. (See "lifting arm

speed control knob" on page 4-25)

POSITION.CONTROl

(1) lowering Speed Control lever

(A) High Speed

(B) low Speed

M46O439A

1. The position control lever is used

to lift or lower the lifting arm (lower

link) of the 3-point hitch.

2. pushing the lever forward lowers

the lower link while pulling the le-

ver backward lifts the lower link.

3. The height of the lower link is pre-

cisely controlled proportional to the

position of the lever.

4. The lower link is lifted by the hy-

draulic energy of the tractor while

it is lowered by potential energy

of its own weight. Therefore, the

implement cannot be lowered by

the hydraulic pressure.

5. Therefore, the implement attached

to the lower link may be lifted by

protrusion on the ground when it is

lowered to the ground. It is called

as "floating."

M46-EU,AU-EEC인증용-05.indd 22

2017-03-10 오전 8:27:41

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды