Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 39 / 192

safetY precautions

(7) part no.: t4182-53191

TO AVOID POSSIBLE INJURY, DEATH OR LOSS OF

PROPERTY FROM A MACHINE RUNAWAY

WARNING

With the engine off, unepected machine movement could

result regardess of the gear shift position.

Before dismounting the machine, apply the parking brake to

prevent machine runaway.

T4182-53191

(8) part no.: t2555-52231

WARNING

T2555-52231

Operate controls only

from Tractor seat.

Failure to comply

could result in

death or serious

injury.

(10) part no.: t2555-52311

T2555-52311

Do Not operate with shield removed.

Failure to comply could result in

death or serious injury.

WARNING

(6) part no.: t2555-52141

WARNING

Before starting and operating

Start engine only from operators seat with

transmission in neutral, PTO disengaged

and hydraulic controls in lowered position.
Slow down on turns, rough ground and

slopes to avoid upset.
Do not permit anyone but the operator

to ride on the tractor, There is no safe

place for riders.
Lock braker together, use warning lights

and SMv emblem while driving on roads.
Lower equipment, place gear shift levers

in neutral, stop engine and apply parking

brake before leaving tractor seat.
Avoid accidlental contact with rear shift

lever while engine is runnung. Unexpected

tractor movement can result.

FAILURE TO FOLLOW ANY OF THE

INSTRUCTIONS ABOVE CAN CAUSE

SEROUS INJURY TO THE OPERATOR OR

OTHER PERSONS.

( Replacement manuals are availeble from your local dealer )

T2555-52141

Know the operating and safety instructions

Cear the area of bystanders.

Locate and know operation of controls.

Fasten your seat belt.

in the operators manual and on the tractor.z

(9) part no.: t2555-52471

T2555-52471

3PT must be

completely raised

prior to adjusting

CUTTING HEIGHT.

M46-EU,AU-EEC인증용-01.indd 29

2017-03-10 오전 8:14:45

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды