Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 105 / 192

opERATIoN

M46O511A

(1) Chocks

(2) parking Brake lever

PARkING

1. This tractor is not equipped with a

separate parking brake. However

uses the brake pedals instead.

2. pull the parking brake lever (2) up

with the brake pedals depressed

fully to engage the pedals with the

latch. If the braking force is insuf-

ficient, depress the pedals more

firmly.

3. Before leaving the tractor after

parking it, make sure to stop the

pTo lower the implement onto the

ground, and stop the engine.

4. If it is necessary to leave the trac-

tor with the engine running, put all

the shift levers in the neutral posi-

tion and apply the parking brake

firmly.

5. When parking the tractor on a

slope, stop the engine with the

parking brake applied and engage

the low speed gear. Also, put the

shuttle shift lever into the forward

driving position on an uphill and

into the reverse driving position on

a downhill.

The. brake. disc. can. be. rap-

idly.worn.if.you.drive.with.the.

parking.brake.applied.

Never.park.the.tractor.on.a.

steep. slope. in. any. circum-

stance..A.severe.accident.can.

happen.

•

WARNING

6. If it is necessary to park the tractor

on a slope with the engine running,

chock all four wheels (1) and per-

form Steps 3 and 4 above.

7. In order to release the parking

brake, depress the brake pedals

firmly again.

M46-EU,AU-EEC인증용-05.indd 15

2017-03-10 오전 8:27:38

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды