Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 123 / 192

3-POINT hITch IMPLEMENT OPERATION

M46O604A

ADjUsTMENT Of sTABILIzER

(1) check Link

(2) Turnbuckle

1. Adjust the check link control hori-

zontal sway of the implement. It is

also used to set the implement on

the back of the tractor in center.

2. To adjust the check link, pull out

the pin and adjust it until the de-

sired transverse moving distance

is obtained.

3. Fit the pin to the fixed hole for nor

mal operation and long hole (mov-

ing) for draft work.

C56O174A

DRAfT HITCH AND TRAILER

(1) draw bar

The draw bar is used to pull an im-

plement, such as a trailer. This trac-

tor is equipped with a fine draw bar.

Make sure to check the max. towing

weight of the trailer and max. vertical

load that can be applied to the draw

bar.

M46O605A

When using an implement that

is attached to the draw bar,

such as a trailer, check if the

towing hitch is firmly attached.

•

CAUTION

M46-EU,AU-EEC인증용-06.indd 7

2017-04-26 오전 11:41:53

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды