Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 163 / 192

maintenance

this service can be affected by the

engine sensitively. therefore, contact

your local

kIOTI

Dealer for this ser-

vice.

ADJUsTING ENGINE VAlVE

ClEARANCE (AE)

if the air cleaner is not in good condi-

tion, the lifetime of the engine can

be shortened, excessive soot can be

produced, and the engine power can

be deteriorated. Therefore, the filter

should be inspected frequently. its

replacement interval can be changed

according to driving conditions. re-

place the filter according to the fol-

lowing proce-dure:
1. open the hood and check the suc-

tion hose and air cleaner housing

for damage.

(1) filter

(2) cap

(3) evacuator valve

REPLACINg AIR CLEANER FILTER (AF)

2. unscrew the air cleaner clip and

remove the cover.

3. clean the inside of the air cleaner

housing by blowing compressed

air through it.

4. replace the filter and check the

housing for damage.

Install the cover and fix it with the clip.

M46O724A

Use only a genuine kIOTI fil-

ter. Use of a non-recommend-

ed filter can cause damage to

the engine and sensor.
Make sure that no dust enters

the system by installing the

cover firmly.

When removing the filter, be

careful not to let foreign mate-

rial enter the air inlet.

•

CAUTION

when installing the cover, make

sure that the dust collection

valve is heading downward.

•

NOTE

M46-EU,AU-EEC인증용-07.indd 29

2017-04-25 오후 5:00:08

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды