Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 86 / 192

Cs2610

Always maintain the proper tire inflation pressure. Make sure the tire pressure

does not exceed the pressure recommended in the manual.

INFlATION PRESSuRE

ITEM

CS2610

Tire sizes

Inflation pressure

Front

Farm

Turf

18 x 8.5 - 8 r3

0.6~1.4 kg/cm², 60~140 Kpa, 8.7~20.3 psi

INd

18 x 8.5 - 8 r4

0.6~1.4 kg/cm², 60~140 Kpa, 8.7~20.3 psi

rear

Farm

Turf

26 x 12.00 - 12 r3

0.8~1.4 kg/cm², 80~140 Kpa, 11.6~20.3 psi

INd

26 x 12.00 - 12 r4

0.8~1.4 kg/cm², 80~140 Kpa, 11.6~20.3 psi

※

INd… for Industrial.

Keep the front tire pressure to maximum if maximum load is applied to the

loader or front weight.
If tires with a different size from the ones already in use are installed, con-

tact the

KIOTI

dealer for the front / rear wheel speed ratio. Improper front /

rear wheel speed ratio can result in excessive wear of the tires.

•
•

NOTE

T46w031A

Do not weld or apply heat to

the tire rim or disc. The tire

can explode due to the rapidly

increased pressure in the tire.

Check tires for inflation pres

sure, damage, deformation,

and extended wear on lug and

damage of rim and disc. Also

check if wheel bolts, rim bolts,

and nuts are loose.

•

wARNING

M46-EU,AU-EEC인증용-04.indd 28

2017-06-16 오후 1:07:08

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды