Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 150 / 192

cs2610

REPLACINg TRANSMISSION FLUId ANd FILTER (M)

the transmission fluid should be

changed if it is contaminated or after

the transmission is serviced.
when changing the transmission

fluid, make sure to change the fluid

filter.
However, replace only the filter after

initial 50 hour operation.

(1) oil filter cartridge

(2) hst hydraulic filter cartridge

M46O713A

1. park the tractor on a level ground

and start the engine to warm it up.

2. stop the engine, apply the parking

brake, and remove the drain plug.

3. to drain the used fluid, place the

oil pan under the transmission

case and turn the drain plug coun-

terclockwise to drain the fluid com

pletely.

If the fluid does not flow out freely,

unscrew the plug on the side of the

hydraulic cylinder on the left of the

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды