Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 177 / 192

storage anD DisPosal

To avoid injury:

never clean the tractor body

while the engine is running.
never run the engine in an

enclosed area without proper

ventilation system in order to

prevent poisoning by exhaust

gas.
When storing the tractor, re-

move the key from the switch

and store it separately in order

to prevent an unauthorized

person from operating the

tractor and being injured.
cover the tractor after the

muffler and the engine have

cooled down.
if the battery is not to be re-

moved, disconnect its nega-

tive terminal. The wiring can

be gnawed by rodents, leading

to a fire.

•
•

•

caUTion

13. apply grease to the exposed cyl-

inder rod.

14. Wash the cooling system and

drain water from it. also, add

anti-freeze.

15. Replace all the oil and filters.
16. Replace the air cleaner filter.

17. Chock the frame in order to re-

move the weight from the tires.

18. set all control systems to neutral

position.

19. Plug any open exhaust pipes.
20. attach a tag onto the tractor to

inform the storage condition of

the tractor.

1. Check the tire air pressure and in-

flate the tires if they are low.

2. install a fully charged battery.
3. Check the fan belt tension.

4. Check all fluid levels. (Engine oil,

transmission / hydraulic oil, engine

coolant and any attached imple-

ments)

5. remove grease from the exposed

cylinder rod.

6. apply grease to the lubrication

points.

7. get onto the tractor and start the

engine.

8. Check if the instrument panel and

all parts operate correctly while

running the engine for a few min-

utes.

9. Drive the tractor outside and check

if it is operating properly. Park the

tractor outside and idle engine for

at least 5 minutes. stop the engine

and visually inspect the tractor.

Check if there is leakage.

Using TracTor afTer sTor-

age

M46-EU,AU-EEC인증용-08.indd 3

2017-03-10 오전 8:51:00

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды