Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 81 / 192

desCrIpTION OF OperATING sysTeM

(1) seat Adjustment Lever

To adjust the seat position, pull the

lever (1) to left under the front of the

seat, slide the seat to the desired po-

sition, and then release the lever.

Make sure that the seat is firmly fixed

by moving it gently after adjustment.

SEAT ADJuSTMENT

SEAT SlIDING

M46O436A

(1) seat belt

SEAT bElT

The seat belt is self-retracting type.

Make sure to fasten the seat belt be-

fore driving.

M46O437A

Always fasten the seat belt

when the tractor has ROPS

properly. Otherwise, never

wear the seat belt.

•

wARNING

Do not put a hand between the

seat and the slides when ad-

justing the seat position. You

can get injured unexpectedly.

•

CAuTION

The seat is equipped with a

safety device that stops the

engine when the driver's seat

is not occupied.
If you leave the seat without

applying of parking brake,

warning buzzer will sound and

parking lamp also will blink for

10 seconds.

•

IMPORTANT

M46-EU,AU-EEC인증용-04.indd 23

2017-06-16 오후 1:07:05

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды