Closet Maid MASTERSUITE Скачать руководство пользователя страница 60

Страница: 60 / 78

PAR

QTY. DESCRIPTION

1 Valet Rod with Housing

1 Slide
2 Set Screws
2 Euro Screws
1 Allen Wrench (included)

1. Separate valet rod housing from slide.

Select installation location, and fasten
two (2) Euro screws through the
corresponding slide holes into the
partition using a Phillips head
screwdriver. (See Fig. 1.)

NOTE: Telescopic Valet Rod includes two sets of

installation holes to align with either the front or

back of the partition. You may position the rod to

INST

ALLA

TION

Fig. 2

Fig. 3

Fig. 1

mount flush to the rear of the partition so that the rod

“ball” retracts completely behind the front edge of the

partition, or, choose the installation holes that align the

housing flush to the front of the partition, leaving the rod

“ball” extended beyond the front edge of the partition.

Slide the telescopic valet rod with housing

over the fastened slide. (See Fig. 2.)

Tighten the rod housing’s two (2) set screws

to secure the housing to the slide using the
Allen Wrench. (See Fig. 3.)

Telescopic Valet Rod may be extended or

retracted as desired. (See Fig. 4.)

Fig. 4

Telescopic Valet Rod

ACCESSORY ASSEMBLY

ORDER OF ASSSEMBL

Shelving /Towers

Drawers and

Doors

Top Shelves and Poles

Adjustable Shelves

Crown Molding

Baskets, Valet Rods,

Tie & Belt Racks, and
other accessories

Islands

Benches

Содержание MASTERSUITE















































































Результаты поиска

Содержание MASTERSUITE

Отзывы:

Похожие инструкции для MASTERSUITE

Бренды по названию

Популярные бренды

Closet Maid MASTERSUITE, Инструкция по сборке, установке и справочник инсталлятора

Результаты поиска

Содержание MASTERSUITE

Отзывы:

Похожие инструкции для MASTERSUITE

Бренды по названию

Популярные бренды