Closet Maid MASTERSUITE Скачать руководство пользователя страница 10

Страница: 10 / 78

Assembly Templates

INTRODUCTION

There are several templates

available to make installation

easier. Each template has a

specific purpose and is intended

to ease and speed up installation

time. It is important to fully

understand which templates

work best with which pieces.

DOOR/HAMPER HINGE TEMPLATE

This template works exactly the same way as the

current Door/Hamper Hinge Template. However, the

holes are in a slightly different location to allow for the

new product. Drill holes with 5mm Self-Centering Drill

Bit (#05-11619).

There are a total of

6 templates

that are needed to properly install

the new 3/4” MasterSuite product

line:
• Shoe Fence - #05-11818

• Door Handle - #05-90050

• Door/Hamper Hinge - #05-90051

• Slide (14”) - #05-90052

• Slide (18”) - #05-90053

TEMPLATES PROVIDED

DOOR HANDLE TEMPLATE

One convenient template is provided for all door

handles, and it works for all handle sizes! To use the

template, simply position the template on door front to

align with the bottom edge of inner door panel (raised
or flat). (See Fig. 1 and Fig. 2.) Drill a 1/16" pilot hole
through the corresponding handle hole(s) on front of
door. Turn the door over and drill a 3/16" hole for
handle at pilot location(s).

Fig. 2

IMPORTANT!

THE NEW MASTERSUITE

3/4” PRODUCT LINE HAS

FOUR (4) NEW TEMPLATES!

Even though the new templates may

look similar to the current Master-

Suite templates you have, it is im-

portant to understand that they are

different. We highly recommend

that you take the time to mark the

new templates as “

New

“ to avoid

any confusion with current Master-

Suite templates! We also recom-

mend that you keep any of your

current templates until you are sure

all of your 5/8” MasterSuite stock

has been depleted.

”

AND 18

”

SLIDE TEMPLATE

To ease working with the template, we have extended

the template toward the front to allow for easier removal

from the side panel! To install slide, push template

prongs into system holes at desired height.

Arrow on

template should point out of cabinet!

Using 5 mm Self-

Centering Bit, drill holes through drill bu

96 mm

128 mm

Fig. 1

Each drawer front is marked on the

back with "dimples" for the various

handle sizes. See "Drawer

Assembly" for more information.

Note, new templates are listed in

bold

(above).

Содержание MASTERSUITE















































































Результаты поиска

Содержание MASTERSUITE

Отзывы:

Похожие инструкции для MASTERSUITE

Бренды по названию

Популярные бренды

Closet Maid MASTERSUITE, Инструкция по сборке, установке и справочник инсталлятора

Результаты поиска

Содержание MASTERSUITE

Отзывы:

Похожие инструкции для MASTERSUITE

Бренды по названию

Популярные бренды