Closet Maid MASTERSUITE Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 78

background image

PAR

TS

QTY. DESCRIPTION

1

Drawer (face, bottom, back and side panels)

2

Drawer Runners (left and right)

2 or 4 Cam locks (6"H = 2; 10"H = 4)

2 or 4

Screw-in Studs (6"H = 2; 10"H = 4)

4 or 6 #6 x 1/2" Screws (for 14" or 18" deep drawers)

4

Euro Screws

Fig. 1

1.

Attach drawer sides to drawer back with

four (4) #8 x 1-1/4” Phillips Head Screws.

INST

ALLA

TION

Fig. 2

Fig. 3

•

Whenever possible for greatest
leverage, mount drawer runners to the
side panels (partitions) while panels are
lying on the floor (before side panels are
mounted in the closet).

•

Similar to basket installation, drawers re-

quire mounting one fixed shelf above and
one below the rack of drawers for stability.

PREP

ARA

TION

1

Drawer Handle (with included handle hardware)

4

#8 x 1-1/4” Phillips Head Screws

14" or 18" Slide Template (#05-90052 or #05-90053)

•

Drawers (and baskets) should never be

mounted behind overlapping sliding doors or
in locations where an open drawer may bump
into another obstacle.

2.

Insert the drawer bottom into the slot

along the bottom of the drawer sides.
(See Fig. 2.) Push the cam locks into
the holes in the drawer sides. Be sure to
orient cams so that the open end of the
cam faces the hole in the front edge.

3.

Locate your selected drawer front(s).

Choose your handle size and drill a

1/16" pilot hole through each corre

sponding

dimple on the back of the drawer front. Turn
the drawer front over and drill a 3/16" hole for
handle at pilot location(s). NOTE: It is im-
portant to drill both the pilot hole through the
back and the regular hole through the front to
prevent chipping.

4.

Attach the drawer handle. (Three sizes of

screws are supplied to accommodate drawer
front styles.) See Fig. 3.

5. Thread 2 (or 4 for 10" drawer) screw-in studs

to drawer front. Attach drawer front to drawer
assembly. Use a Phillips screwdriver to tighten
cam locks.

Drawer

DOOR & DRAWER ASSEMBLY

CAM LOCKS

96 mm

128 mm

48

ORDER OF ASSSEMBL

Y

£

Shelving /Towers

¢

Drawers and

Doors

£

Top Shelves and Poles

£

Adjustable Shelves

£

Crown Molding

£

Baskets, Valet Rods,

Tie & Belt Racks, and
other accessories

£

Islands

£

Benches

«
...
46
47
48
49
50
...
»

Содержание MASTERSUITE















































































Отзывы:

Нет отзывов

Похожие инструкции для MASTERSUITE

Бренд: MANCHESTER WOOD Страницы: 4

Бренд: baby&child Страницы: 3

Бренд: NABBI Страницы: 16

Бренд: ofichairs Страницы: 2

Бренд: fantastic furniture Страницы: 12

Бренд: fantastic furniture Страницы: 6

Бренд: fantastic furniture Страницы: 11

Бренд: fantastic furniture Страницы: 9

Бренд: FANCII Страницы: 12

Бренд: GABBY Страницы: 4

Бренд: Yo-Yo Desk Страницы: 2

San Fran 2 Person Run Workstation

Бренд: Jason.L Страницы: 4

Бренд: Dancover Страницы: 15

Norm Architects Naervaer NA10

Бренд: &Tradition Страницы: 6

Бренд: HOMCOM Страницы: 4

Бренд: Gautier Страницы: 20

Бренд: Nipsti Страницы: 8

Urban 3 Drawer Chest

Бренд: The Home And Office Stores Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды