Closet Maid MASTERSUITE Скачать руководство пользователя страница 50

Страница: 50 / 78

•

Hamper Doors must be installed with

a fixed shelf at both the top and bottom

of the door. The distance from the

vertical center of the bottom fixed shelf

to the vertical center of the top fixed

shelf totals 23-7/8”.

PREP

ARA

TION

In one hand, hold the Door/Hamper

Template (#05-90051)with the wooden

handle flush against the front edge of the

bottom, fixed shelf (and against the left or

right partition). With your free hand, drill

your hinge holes, using the Self Center

Drill Bit, through the Lucite template’s

holes. (See Fig. 1.)

INST

ALLA

TION

PAR

QTY. PART DESCRIPTION

1 Hamper Door (contoured, raised panel or solid wood)
1 17”h x 24”w or 30”w Basket (no slides required)

Door/Hamper Template (#05-90051)

Self Center Drill Bit (#05-11619)

Hamper Door Hardware Kit:

4 Euro Screws
4 #8 x 5/8” Screw

2 #8 x 1/2" Screws
2 Mounting Plates

2 Hinges

2 Flap Stays

1 Basket Rail

•

For toekicks in floor-mounted systems,

count holes up from the bottom of each
tower, and drill out the second and
fourth holes for attaching the nailers,
using HiLow screws.

Repeat step 1 for the opposite hinge hole

locations.

Attach the two hinge plates with pre-

mounted screws to the holes in the bottom

shelf you drilled in steps 1 and 2.

Fig. 1

Hamper Door

DOOR & DRAWER ASSEMBLY

ORDER OF ASSSEMBL

Shelving /Towers

Drawers and

Doors

Top Shelves and Poles

Adjustable Shelves

Crown Molding

Baskets, Valet Rods,

Tie & Belt Racks, and
other accessories

Islands

Benches

Содержание MASTERSUITE















































































Результаты поиска

Содержание MASTERSUITE

Отзывы:

Похожие инструкции для MASTERSUITE

Бренды по названию

Популярные бренды

Closet Maid MASTERSUITE, Инструкция по сборке, установке и справочник инсталлятора

Результаты поиска

Содержание MASTERSUITE

Отзывы:

Похожие инструкции для MASTERSUITE

Бренды по названию

Популярные бренды