Closet Maid MASTERSUITE Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 78

background image

These instructions apply to corner towers

using shelves or hanging. Please note that

corner towers using the radius hanging bar

should be matched with the large radius

fixed cam corner shelves. The regular cam

and adjustable corner shelves do not match

the radius curve of the hanging bar.

PREP

ARA

TION

Further, use of either radius fixed corner

shelf at the top of the tower will not match

PAR

TS

QTY. DESCRIPTION

2 Corner Cam Fixed Shelves
4    Corner Adjustable Shelves (optional)
3    Vertical Partitions (Floor Mounted System only)
1    30" Cleat
2    4.5 x 60 mm (2-3/8”) screws with cover caps
24    Safety Shelf Pins (6 per adjustable corner shelf)
16    HiLow Screws

Screw-In and/or Double-Sided Studs (as needed)

Assorted closet components

with the continuous top shelf material, so it is

not recommended to use a cammed top shelf IF

you will also be installing continuous top shelf

material.

•

In most cases, corner towers should be

assembled and installed in the closet before
installing other towers and hanging sections
along the walls.

•

When one or more corner towers have been

installed, you may continue regular
installation of adjoining hanging and
shelving sections.

•

You may

not

install corner towers using the

rail hanging MasterSuite system.

•

We recommend cutting one (or more) 30”

cleat(s) to support and square one side of the
corner tower section. Prior to assembly, cut a
30” shelf tower cleat to 29-3/8” wide and drill
out dowel (8mm) and HiLow Screw (4 mm)
holes. See Fig. 1.

Corner Tower

SHELVING/TOWER ASSEMBLY

Unfinished Edge

Finished Edges

30”

29-3/8”

2.13”
54mm

.87”/22mm

3.39”
86mm

8mm

4mm

TRIM EACH 30" CLEAT TO 29-3/8". THEN,

DRILL HOLES FOR TWO (2) DOWELS AND

ONE HOLE FOR ONE (1) HI-LOW SCREW

Fig. 1

29

ORDER OF ASSSEMBL

Y

¢

Shelving /Towers

£

Drawers and

Doors

£

Top Shelves and Poles

£

Adjustable Shelves

£

Crown Molding

£

Baskets, Valet Rods,

Tie & Belt Racks, and
other accessories

£

Islands

£

Benches

CLEAT

«
...
27
28
29
30
31
...
»

Содержание MASTERSUITE















































































Отзывы:

Нет отзывов

Похожие инструкции для MASTERSUITE

Бренд: Gazelle Страницы: 6

Бренд: Safco Страницы: 2

Space Seating 13-37N1P3

Бренд: Office Star Страницы: 2

JENSEN 5-PIECE DINING SET

Бренд: Canvas Страницы: 20

Бренд: ofichairs Страницы: 2

Бренд: NABBI Страницы: 12

Бренд: Yaasa Страницы: 10

Бренд: Yaasa Страницы: 92

Бренд: Dancover Страницы: 15

Бренд: Gami Страницы: 3

Hampshire Tall Bookcase

Бренд: The Land of Nod Страницы: 4

Addison Lift-Top 3524DUETb

Бренд: Whittier Wood Furniture Страницы: 4

Бренд: Allen + Roth Страницы: 24

Бренд: Naterial Страницы: 52

Бренд: Riotoro Страницы: 31

Бренд: Nucraft Страницы: 13

TIVERTON T1VEDINIBULK

Бренд: BARKER AND STONEHOUSE Страницы: 12

Бренд: FAAC Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды