Closet Maid MASTERSUITE Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 78

background image

Hints, Tips & Ordering

INTRODUCTION

24" MATERIAL

HARDWARE

The following is a quick-reference

guide to the exciting new line of

MasterSuite 3/4" products! These

"tidbits" will prove helpful for under-

standing, ordering and installing the

new line! Please refer to this page

as often as necessary while familiar-

izing yourself with the new line.

Studs:

• There are new screw-in studs

(#56544) and double-sided studs
(#56534).

Cams:

• A new, single hole cam is now

used for all MasterSuite
components!

• To tighten cams, hold screw-

driver at a

25-degree angle

. See

Fig. 1 below.

• Cam hole is 20 mm.
• Current cam lock drill tools can

still be used to make custom
cam shelves.

o Hettich tool

• Adjust depth setting to “15”

• Drill only 20 mm hole.

• 24" deep material is available in

white only

and is

available in two shelf widths: 24" and 30".

•  Cam shelf uses 3 cams per side.
•  Drawers can be added by using 18" drawer boxes.
•  To install drawer slide, attach slide to panel with Euro

screw in front system hole. (Slide will be flush with
front of panel.) Place small torpedo level on slide.
Once leveled, screw back part of slide to panel by
driving a #6 x 5/8” screw. There is no need for a
pre-drilled hole.

• Hang rod can be installed on center set system holes.

CLEATS

•

We strongly recommend using a cleat for any system
which could have the potential to hold heavy duty
items or be used at a maximum weight capacity.

Interview client to determine future use! We also
recommend using a cleat at the top of any 60" or 80"
thru-drilled panel and in the center tower of any
hanging tower system.

• Cleats now have two (2) pre-installed dowels (per

side) and one (1) hole in each side for a screw. This is
opposite of the old cleat, so please make note! Use
one (1) HiLow screw to secure cleat to side panel.

HUTCH

• Shelves and drawers, along with hardware, are sold

separately.

• There are no more "packs" except for panel packs

(2 per box—left and right, if stop drilled).

• 20" hutch shelves: adjustable shelf and fixed cam

shelf. Each is sold with three (3) per box. (For top
section shelves, use standard 14" depth shelves.)

• Two new hutch drawer boxes:

6"H x 18" deep and

10"H x 18" deep (both available in 24" or 30" widths).

• To install drawer slide, attach slide to panel with Euro

screw in front system hole. Back hole will need to
be drilled. Use template (#05-90053) and drill with
5mm Self-Centering Bit (#05-11619).

8

25˚

Fig. 1

«
...
6
7
8
9
10
...
»

Содержание MASTERSUITE















































































Отзывы:

Нет отзывов

Похожие инструкции для MASTERSUITE

Бренд: PAIDI Страницы: 3

Clinician Premiere Series

Бренд: OAKWORKS Страницы: 28

Clinician Premiere

Бренд: OAKWORKS Страницы: 24

Findley & Myers CBD36

Бренд: CABINETS TO GO Страницы: 4

Бренд: Coaster Страницы: 3

Бренд: DHP Страницы: 19

Бренд: Whalen Страницы: 18

ARDWICK Ottoman TV Bed

Бренд: Happybeds Страницы: 24

Бренд: OK DIGITAL Страницы: 22

Бренд: Next Страницы: 14

Damhus 115320/701-206-1018

Бренд: Jysk Страницы: 14

FOLDING PROCESSING TABLE

Бренд: Bass Pro Shops Страницы: 2

TRENDY Woodie 66094

Бренд: deVRIES Страницы: 8

Бренд: MARCKERIC Страницы: 18

MS55-018-039-23

Бренд: Mainstays Страницы: 12

FARMHOUSE WOOD DINING WITH PICNIC BENCHES...

Бренд: HAMPTON BAY Страницы: 18

Бренд: HABYS Страницы: 20

Бренд: J&K Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды