Closet Maid MASTERSUITE Скачать руководство пользователя страница 7

Страница: 7 / 78

INSTALLATION APPOINTMENT ORDER

Assemble or Install

Description of Action

Bring tools and product to site location, ensuring finished

walls and hardwood floors are protected from dings by
laminate. Use empty packaging, blanket or cloth underneath
laminate on hardwood floors.

Customer Review
and
Payment Collection

Double-check your installation against the design plans.

Ensure all shelves, drawers and other accessories are in correct

place. Demonstrate to client, if available, how to adjust shelf

height, etc. Collect payment, if applicable, from client.

Unload Product and
Tools

If removal of existing, built-in shoe racks, cabinetry or

cleats and baseboard is necessary, tearout must be completed

before installation of new system. (For safety, ensure nails or

other fasteners are removed or bent down on the loose

materials removed from the closet.)

Tearout

Install all closet systems.

Install Closet Product

Wipe down all shelves, poles and partitions with soft cloth.

Clean with household cleaner.

Clean Closet
System(s)

Vacuum the floor where parts were assembled and stored

while in assembly process.

Vacuum

Installation Order - 3

INTRODUCTION

Remove Waste and
Tools

Inspect Site

Arrival

Arrive on site. Greet customer, if available. Review

installation process with client, if available.

Inspect installation site with design plans in hand and tape

measure. Verify all clothing has been removed and closet
is prepared for installation. Double check closet measurements
against plans. If there are no major obstacles to installation
(i.e. drastically incorrect measurements requiring new

closet components), determine best route to transport tools

and closet parts to site.

Remove waste from top shelves and other parts. Take tools to

truck.

Содержание MASTERSUITE















































































Результаты поиска

Содержание MASTERSUITE

Отзывы:

Похожие инструкции для MASTERSUITE

Бренды по названию

Популярные бренды

Closet Maid MASTERSUITE, Инструкция по сборке, установке и справочник инсталлятора

Результаты поиска

Содержание MASTERSUITE

Отзывы:

Похожие инструкции для MASTERSUITE

Бренды по названию

Популярные бренды