manualshive.com logo in svg

Cisco Catalyst 6509, Руководство пользователя программного обеспечения

Скачайте бесплатное программное руководство для Cisco Catalyst 6509 с нашего веб-сайта. Получите доступ к полезной информации о настройке и использовании этого высокопроизводительного устройства. Подробное руководство поможет вам использовать все возможности Cisco Catalyst 6509. manualshive.com - ваш источник руководств по оборудованию.

Поделиться
Скачать
background image

 

15-11

Catalyst 6500 Series Switch Software Configuration Guide—Release 8.7

OL-8978-04

Chapter 15      Configuring Access Control

Using Cisco IOS ACLs in your Network

These sections describe how the different types of ACLs and traffic flows are handled by the hardware 
and the software:

•

Security Cisco IOS ACLs, page 15-11

•

Reflexive ACLs, page 15-11

•

TCP Intercept, page 15-11

•

Policy Routing, page 15-12

•

WCCP, page 15-12

•

NAT, page 15-12

•

Unicast RPF Check, page 15-12

•

Bridge-Groups, page 15-12

Security Cisco IOS ACLs

The IP and IPX security Cisco IOS ACLs with PFC are as follows:

•

The flows that match a “deny” statement in a security ACL are dropped by the hardware if 
“ip unreachables” is disabled. The flows matching a “permit” statement are switched in the 
hardware.

•

Permit and deny actions of the standard and extended ACLs (input and output) for security access 
control are handled in the hardware.

•

IP accounting for an ACL access violation on a given interface is supported by forwarding all denied 
packets for that interface to the software without impacting other flows.

•

Dynamic (lock and key) ACL flows are supported in the hardware; however, idle timeout is not 
supported.

•

IPX standard input and output ACLs are supported in the hardware when the ACL parameters are 
IPX source network, destination network, and/or destination node. If the ACL contains any other 
parameters, it is handled in the software.

•

IPX extended input and output ACLs are supported in the hardware when the ACL parameters are 
IPX source network, destination network, destination node, and/or protocol type. 

•

ACL flows requiring logging are handled in the software without impacting non-log flow forwarding 
in the hardware. 

Reflexive ACLs

Up to 512 simultaneous reflexive sessions are supported in the hardware. When the reflexive ACLs are 
applied, the flow mask is changed to VLAN-full flow.

TCP Intercept

TCP intercept implements the software to protect the TCP servers from the TCP SYN-flooding attacks, 
which are denial-of-service attacks. TCP intercept helps prevent the SYN-flooding attacks by 
intercepting and validating the TCP connection requests. In intercept mode, the TCP intercept software 
intercepts the TCP synchronization (SYN) packets from the clients to the servers that match an extended 
access list. The software establishes a connection with the client on behalf of the destination server, and 
if successful, establishes the connection with the server on behalf of the client and binds the two 

Содержание Catalyst 6509

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6509

Allied Telesis AT-9424Ts/XP AC Datasheet preview
AT-9424Ts/XP AC
Бренд: Allied Telesis Страницы: 3
KEMP Technologies LoadMaster 1500 Installation And Configuration Manual preview
LoadMaster 1500
Бренд: KEMP Technologies Страницы: 71
U.S. Products maxg Quick Installation Manual preview
maxg
Бренд: U.S. Products Страницы: 80
National Instruments NI-9206 Getting Started preview
NI-9206
Бренд: National Instruments Страницы: 8
WABCO CAN Router Manual preview
CAN Router
Бренд: WABCO Страницы: 29
Aaeon SBC-657B Manual preview
SBC-657B
Бренд: Aaeon Страницы: 61
Gigabyte GN-WLMA101 User Manual preview
GN-WLMA101
Бренд: Gigabyte Страницы: 18
Avenview DVI-PROWALL-9X Instruction Manual preview
DVI-PROWALL-9X
Бренд: Avenview Страницы: 28
TRENDnet TEW-641PC Quick Installation Manual preview
TEW-641PC
Бренд: TRENDnet Страницы: 12
Radio Shack Bluespoon 17-1000 Quick Start Manual preview
Bluespoon 17-1000
Бренд: Radio Shack Страницы: 1
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Бренд: Patton electronics Страницы: 145
AOpen ISDN SOHO Router User Manual preview
ISDN SOHO Router
Бренд: AOpen Страницы: 89
Technics SH-GE90 Service Manual preview
SH-GE90
Бренд: Technics Страницы: 20
uneron eSOM3735z Quick Start Manual preview
eSOM3735z
Бренд: uneron Страницы: 13
Addonics Technologies Network Adapter ADZIFCF Installation Manual preview
Network Adapter ADZIFCF
Бренд: Addonics Technologies Страницы: 1
Juniper TX MATRIX Hardware Manual preview
TX MATRIX
Бренд: Juniper Страницы: 396
Stepper Motor Canada DB25-1205F Manual preview
DB25-1205F
Бренд: Stepper Motor Canada Страницы: 5
Doro GW7001 Quick Installation Manual preview
GW7001
Бренд: Doro Страницы: 50

Бренды по названию

Популярные бренды

Загрузить еще бренды