Cisco Catalyst 6509 Скачать руководство пользователя страница 1170 | Manualshive

Страница: 1170 / 1488

background image

49-8

Catalyst 6500 Series Switch Software Configuration Guide—Release 8.7

OL-8978-04

Chapter 49 Configuring SPAN, RSPAN and the Mini Protocol Analyzer

Configuring SPAN on the Switch

•

If any of the VLANs on the SPAN source port(s) are blocked by spanning tree, you may see extra
packets that are transmitted on the destination port(s) that were not actually transmitted out the
source port(s). The extra packets are sent through the switch fabric to the source port and are blocked
by spanning tree at the source port.

Caution

In software releases before software release 8.4(1), if you used the

set span

command without the

create

keyword, and you had only one session configured, the session was overwritten. If two SPAN sessions
were already configured, you received an error message. If a matching destination port existed, the
particular session was overwritten (with or without specifying the

create

keyword). If you specified the

create

keyword and there was no matching destination port, the session was created.

In software release 8.4(1) and later releases, the

create

keyword has been removed from the

set span

command. When you enable a SPAN session without the

create

keyword, and another session is

available, the first session is not overwritten.

Configuring SPAN from the CLI

To configure SPAN, you specify the source, the destination ports, the direction of the traffic through the
source that you want to mirror to the destination ports, and if the destination port can receive the packets.

To configure a SPAN port, perform this task in privileged mode:

Caution

If the SPAN destination port is connected to another device and you enable reception of the incoming
packets (using the

inpkts

enable

keywords), the SPAN destination port receives the traffic for whatever

VLAN to which the SPAN destination ports belong. The SPAN destination port does

not

participate in

spanning tree for that VLAN. Use caution when using the

inpkts

keyword to avoid creating network

loops with the SPAN destination port or assigning the SPAN destination port to an unused VLAN.

This example shows how to configure SPAN so that both the transmit and receive traffic from port 1/1
(the SPAN source) is mirrored on port 2/1 (the SPAN destination):

Console> (enable)

set span 1/1 2/1

Destination : Port 2/1

Admin Source : Port 1/1

Oper Source : Port 1/1

Direction : transmit/receive

Incoming Packets: disabled

Learning

: enabled

Multicast

: enabled

Filter

: -

Task

Command

Step 1

Configure the SPAN source and destination ports.

set span

{

src_mod/src_ports

|

src_vlans

|

sc0

}

{

dest_mod/dest_port

} [

rx

|

tx

|

both

]

[

session

session_number

] [

inpkts

{

enable

|

disable

}] [

learning

{

enable

|

disable

}]

[

multicast

{

enable

|

disable

}] [

filter

vlans...

]

Step 2

Verify the SPAN configuration.

show span

«
...
1168
1169
1170
1171
1172
...
»

Содержание Catalyst 6509

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6509

Бренд: Data Translation Страницы: 60

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 86

Бренд: IEI Technology Страницы: 187

Бренд: IEI Technology Страницы: 71

Бренд: Pima Страницы: 4

Бренд: Tripp Lite Страницы: 2

Бренд: HARTING Страницы: 13

Бренд: Paradyne Страницы: 23

Vigor 2760 Series

Бренд: Draytek Страницы: 54

System Storage DS3200

Бренд: IBM Страницы: 2

Бренд: ZKTeco Страницы: 68

FlexNetwork 5130 Series

Бренд: HPE Страницы: 33

Бренд: Aaeon Страницы: 72

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

S3000-EI Series

Бренд: Quidway Страницы: 16

LEDWALL Optimizer HQ P2

Бренд: Gundermann VIDEOWALL Страницы: 12

Бренд: Tripp Lite Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды