manualshive.com logo in svg

Cisco Catalyst 6509, Руководство пользователя программного обеспечения

Скачайте бесплатное программное руководство для Cisco Catalyst 6509 с нашего веб-сайта. Получите доступ к полезной информации о настройке и использовании этого высокопроизводительного устройства. Подробное руководство поможет вам использовать все возможности Cisco Catalyst 6509. manualshive.com - ваш источник руководств по оборудованию.

Поделиться
Скачать
background image

 

7-13

Catalyst 6500 Series Switch Software Configuration Guide—Release 8.7

OL-8978-04

Chapter 7      Configuring Spanning Tree

Understanding How PVST+ and MISTP Modes Work

An overview of each mode is provided in this section. Each mode is described in detail in these sections:

•

Configuring PVST+ on the Switch, page 7-26

•

Configuring MISTP-PVST+ or MISTP on the Switch, page 7-34

Caution

If your network currently uses PVST+ and you plan to use MISTP on any switch, you must first enable 
MISTP-PVST+ on the switch and configure an MISTP instance to avoid causing loops in the network.

PVST+ Mode

PVST+ runs on each VLAN on the switch, ensuring that each VLAN has a loop-free path through the 
network. 

PVST+ provides Layer 2 load balancing for the VLAN on which it runs; you can create different logical 
topologies using the VLANs on your network to ensure that all the links are used and no link is 
oversubscribed.

Each PVST+ instance on a VLAN has a single root switch. This root switch propagates the spanning-tree 
information that is associated with that VLAN to all other switches in the network. This process ensures 
that the network topology is maintained because each switch has the same knowledge about the network.

Rapid-PVST+

With software release 8.1(1) and later releases, Rapid-PVST+ is the default spanning-tree protocol that 
is used on all Ethernet, Fast Ethernet, and Gigabit Ethernet port-based VLANs on Catalyst 6500 series 
switches. Rapid-PVST+ is similar to PVST+. The only difference is that Rapid-PVST+ uses a rapid STP 
that is based on IEEE 802.1w instead of 802.1D. Rapid-PVST+ uses the same configuration as PVST+ 
with minimal additional configuration. See the 

“Configuring Rapid-PVST+ on the Switch” section on 

page 7-33

 for configuration information. In Rapid-PVST+, dynamic CAM entries are flushed 

immediately on a per-port basis when any topology change is made. UplinkFast and BackboneFast are 
enabled, but not active in this mode, as the functionality is built into the rapid STP. Rapid-PVST+ 
provides for rapid recovery of connectivity following the failure of a bridge, bridge port, or LAN.

A port that is connected to a nonbridging device (for example, a host or a router) is an edge port. A port 
that connects to a hub is also an edge port if the hub or any LAN that is connected by it does not have a 
bridge. An edge port can start forwarding as soon as the link is up. You must explicitly configure the 
ports that are connected to the hosts and routers as edge ports while using Rapid-PVST+. 

For complete protocol details

, 

see the 

“Rapid Spanning Tree Protocol” section on page 7-18

.

MISTP Mode

MISTP is an optional spanning-tree protocol that runs on Catalyst 6500 series switches. MISTP allows 
you to group multiple VLANs under a single instance of spanning tree (an MISTP instance). MISTP 
combines the Layer 2 load-balancing benefits of PVST+ with the lower CPU load of IEEE 802.1Q.

An MISTP instance is a virtual logical topology that is defined by a set of bridge and port parameters. 
When you map VLANs to an MISTP instance, this virtual logical topology becomes a physical topology. 
Each MISTP instance has its own root switch and a different set of forwarding links (different bridge 
and port parameters). 

Содержание Catalyst 6509

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6509

FabiaTech FX5638 Series Users Quick Reference preview
FX5638 Series
Бренд: FabiaTech Страницы: 4
ICP DAS USA ZT-2510 Series Quick Start Manual preview
ZT-2510 Series
Бренд: ICP DAS USA Страницы: 8
Paradyne COMSPHERE 3800 Series Release Note preview
COMSPHERE 3800 Series
Бренд: Paradyne Страницы: 88
Paradyne COMSPHERE 3800PLUS Supplementary Manual preview
COMSPHERE 3800PLUS
Бренд: Paradyne Страницы: 5
Paradyne Hotwire 6212 Quick Installation Instructions preview
Hotwire 6212
Бренд: Paradyne Страницы: 2
TC Electronic ATAC Service Manual preview
ATAC
Бренд: TC Electronic Страницы: 55
Texas Instruments ThunderLAN TNETE100A Programmer'S Manual preview
ThunderLAN TNETE100A
Бренд: Texas Instruments Страницы: 179
Orban OPTIMOD 6300 Operating Manual preview
OPTIMOD 6300
Бренд: Orban Страницы: 255
Stephen STES2026 Configuration Manual Manual preview
STES2026
Бренд: Stephen Страницы: 102
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Бренд: UNA AUTOMATION Страницы: 20
DFRobot FIT0677 Assembly Manual preview
FIT0677
Бренд: DFRobot Страницы: 30
Edimax GS-5208PLG V2 Quick Installation Manual preview
GS-5208PLG V2
Бренд: Edimax Страницы: 15
TP-Link JetStream T2600G-28TS User Manual preview
JetStream T2600G-28TS
Бренд: TP-Link Страницы: 1136
DTS XD10P Installation And Operation Manual preview
XD10P
Бренд: DTS Страницы: 94
Brickcom NR-2008 User Manual preview
NR-2008
Бренд: Brickcom Страницы: 184
MACHINIST X79-Z9-D7 User Manual preview
X79-Z9-D7
Бренд: MACHINIST Страницы: 15
peplink Balance 380 User Manual preview
Balance 380
Бренд: peplink Страницы: 111
G&D DP1.2-Vision-IP-Fiber Installation And Operation Manual preview
DP1.2-Vision-IP-Fiber
Бренд: G&D Страницы: 240

Бренды по названию

Популярные бренды

Загрузить еще бренды