Cambium Networks PMP 450 Series Скачать руководство пользователя | Manualshive

Страница: 35 / 292

background image

Chapter 1: Product description

35

(TDD). The AP operates in TDMA mode to service multiple SMs.

Applications for the PMP Series include:

l

High throughput enterprise applications

l

nLOS video surveillance in metro areas

l

Urban area network extension

l

Network extension into areas with foliage

Point-to-Point ( Backhaul)

The PTP configuration of 450 Platform Family consists of two BH (Backhaul) ODUs. The customer can
decide, via software configuration, if this unit is a BHM (Backhaul Master) or a BHS (Backhaul Slave). The
radio link operates on a single frequency channel using Time Division Duplex (TDD). The BHM operates in
TDMA mode to service the BHS.

Applications for the PTP Series include:

l

Enterprise Access

l

nLOS video surveillance

l

Leased line replacements and backup solutions

l

Network extension

Product variant s

The 450 Platform Family is available in the following product variants:

l

The ODU is supplied in the following regional variants:

l

FCC, intended for deployment in the USA

l

IC, intended for deployment in Canada

l

EU, intended for deployment in countries of the European Union or other countries following
ETSI regulations

l

Rest of the World (RoW), intended for deployment in countries other than USA and EU
countries.

l

Integrated, connectorized ODUs:

l

Integrated units contain an integrated antenna.

l

Connectorised units are designed to connect to an external antenna.

l

450b High Gain units operate with a purpose designed dish.

l

Standard or ruggedized ODUs:

l

APs and SMs are supplied in either ruggedized or standard versions.

l

450b range are supplied to the IP55 standard, but an IP67 conversion kit is available for the
High Gain units.

l

Encryption:

l

Most ODU variants in the range support AES 128 or AES 256 encryption.

l

ODU variants are available with weaker or no encryption for export purposes.

l

Power supply modules: A variety of Power Supplies / Power-over-Ethernet (PoE) supplies are
available

«
...
33
34
35
36
37
...
»

Содержание PMP 450 Series





































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PMP 450 Series

DIR-450 - 3G Mobile Router Wireless

Бренд: D-Link Страницы: 79

Бренд: T-Mobile Страницы: 8

Бренд: T-Mobile Страницы: 3

Бренд: Linkskey Страницы: 8

Бренд: EAS Electric Страницы: 110

Бренд: NETGEAR Страницы: 263

Бренд: NETGEAR Страницы: 22

RangeMax NEXT WNR834A

Бренд: NETGEAR Страницы: 106

Бренд: ALCON Страницы: 47

Бренд: H3C Страницы: 19

Бренд: Ebyte Страницы: 26

Бренд: Planet Страницы: 8

Бренд: bintec elmeg Страницы: 66

Бренд: Linksys Страницы: 30

Бренд: Linksys Страницы: 31

Бренд: Linksys Страницы: 135

1130AG - Aironet - Wireless Access Point

Бренд: Cisco Страницы: 48

Бренд: D-Link Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды