Cambium Networks PMP 450 Series Скачать руководство пользователя

Страница: 196 / 292

Chapter 4: Preparing for installation

196

Pin Signal

Pair

Color

TP4+

White/brown stripe

TP4-

Brown solid

RJ- 4 5 Pinout for Crossover Et hernet Cable

Figure 76 :

Crossover Ethernet Cable

Table 121 :RJ-45 pinout for crossover Ethernet cable

Connection 1

Connection 2

Signal

Pair

Color

Signal

Pair

Color

TP1+

White/orange stripe

TP2+

White/green stripe

TP1-

Orange solid

TP2-

Green solid

TP2+

White/green stripe

TP1+

White/orange stripe

TP3+

White/blue stripe

TP4+

White/brown stripe

TP3-

Blue solid

TP4-

Brown solid

TP2-

Green solid

TP1-

Orange solid

TP4+

White/brown stripe

TP3+

Blue solid

TP4-

Brown solid

TP3-

White/blue stripe

AP/ BHM t o UGPS cable

The AP/BHM to UGPS cable can be constructed from RJ12 to RJ 45 cable using the pin configuration
described in AP/BHM to UGPS cable pinout.

Note

This is only applicable for 450 AP/BHM.

The AP/BHM will only power up the UGPS if it configured to do so.

Figure 77 :

AP/BHM to UGPS cable

Содержание PMP 450 Series





































































































































































































































































































Результаты поиска

Содержание PMP 450 Series

Отзывы:

Похожие инструкции для PMP 450 Series

Бренды по названию

Популярные бренды

Cambium Networks PMP 450 Series, Руководство по установке

Результаты поиска

Содержание PMP 450 Series

Отзывы:

Похожие инструкции для PMP 450 Series

Бренды по названию

Популярные бренды