Brother GTX pro Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 356

Brother GTX pro Скачать руководство пользователя страница 45

45

Installation and preparation

4-3-1. Installing printer driver onto your PC

To begin with, on your PC, install the printer driver for file output, "Brother GTX pro FileOutput".
At this stage, do not connect the printer to your PC yet.
<TIPS>



You must log into your PC with administrator privileges.

(1)

Activate the PC.

(2)

Complete all of the current sessions.

(3)

Double-click on the "setup.exe" to execute the installer.

(4)

Then, the installation procedures will begin. Follow the on-screen instructions to complete the installation.

(5)

When the dialog box shown below appears, click [Install].

(6)

After the installation is completed, reactivate the PC.

«
...
43
44
45
46
47
...
»

Содержание GTX pro





































































































































































































































































































































































Отзывы:

Нет отзывов