Brother GTX pro Скачать руководство пользователя страница 142

Страница: 142 / 356

142

Basic printing procedures

From the lowest position to the middle position

(1)

Detach the platen.

(2)

Remove the platen fixing lever, platen height adjustment lever.

The number of collars and the height adjustment range are as follows:

Position

Height

No. of collars

Highest position
(standard)

0 to 10 mm

Middle position

10 to 20 mm

Lowest position

20 to 30 mm

None

Case of 16×21 platen

Position

Height

No. of collars

Lowest position

0 to 10 mm

None

<TIPS>



Spacers are installed on your printer so that the height can be the reference value. Do not change the number of spacers.

X0266

(3)

Loosen the knob while holding the platen bearing and lift the platen bearing to the top to tighten the knob again.

X0267

Platen height adjustment lever

Platen fixing lever

Platen bearing

Knob

Spacer

Содержание GTX pro





































































































































































































































































































































































Результаты поиска

Содержание GTX pro

Отзывы:

Brother GTX pro, Инструкция по эксплуатации, Страница: 142 / 356

Результаты поиска

Содержание GTX pro

Отзывы: