Brother GTX pro Скачать руководство пользователя страница 195

Страница: 195 / 356

195

Precautions to keep good printing quality/use printer over the long term

(8)

With the clean stick R, wipe away the ink mist on the carriage roller part.

(9)

Move the carriage from side to side to rotate the roller part, and wipe all around the carriage roller.

X0448

(10)

Clean the carriage guide shaft and the three sides (upper, front, and lower sides across which the roller rolls) of

roller guide.
<TIPS>



Moisten a waste cloth (non-fuzzy cloth) with a small amount of alcohol, and use such cloth to wipe clean the internal
surface.



Do not use alcohol on parts other than the carriage guide shaft and the roller guide.

(11)

Apply a proper amount of the grease (which is included with the printer) onto the carriage guide shaft.
<CAUTION>



When handling the grease, perform the work operation in such a manner that it will not get into your eyes or onto your skin.

X0063

Roller guide

Carriage guide shaft

Front cover

Carriage roller

Clean stick R

Carriage

Содержание GTX pro





































































































































































































































































































































































Результаты поиска

Содержание GTX pro

Отзывы:

Brother GTX pro, Инструкция по эксплуатации, Страница: 195 / 356

Результаты поиска

Содержание GTX pro

Отзывы: