Brother GTX pro Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 356

Brother GTX pro Скачать руководство пользователя страница 141

141

Basic printing procedures

(6)

Use the platen fixing lever to secure the platen temporarily.

The number of collars and the position of screw hole for the platen bearing differ by the height of the platen
adjusted.
<TIPS>



If you are setting the platen's height to the lowest position, remove all the collars and fix the platen bearing at
its highest screw hole temporarily.



If you are setting the platen's height to the middle position, attach one collar and fix the platen bearing at its
middle screw hole temporarily.



If you are setting the platen's height to the highest position, attach two collars and fix the platen bearing at its
lowest screw hole temporarily.

X0264

(7)

Tighten the knob to secure the platen bearing in place.

<TIPS>



Align the center of platen fixing lever with the position as illustrated in the figure below, and secure the platen
bearing in place.

X0265

(8)

Insert the platen to be used and tighten the platen fixing lever.

Platen fixing lever

Platen bearing

Knob

Platen fixing lever

Platen fixing lever

Platen bearing

Center
position
alignment

Platen bearing

Knob

Platen bearing

«
...
139
140
141
142
143
...
»

Содержание GTX pro





































































































































































































































































































































































Отзывы:

Нет отзывов