Brother GTX pro Скачать руководство пользователя страница 175

Страница: 175 / 356

175

Precautions to keep good printing quality/use printer over the long term

(5)

Open the front cover, and clean each of the nozzle guards, wipers, exhaust caps, and suction caps.

Two types of clean sticks are provided. Use either the clean stick T or R depending on what you want to clean.

<TIPS>



For the cleaning method, refer to the description mentioned below.

X0319

(6)

After the cleaning is completed, close the front cover.

(7)

Turn on the power.

<NOTE>



Dispose of any waste resulting from the cleaning in accordance with applicable laws and ordinances.

<TIPS>



Then, a head cleaning will be performed to prevent any ink from drying up.



Because the cleaning cup will be reused, rinse it in clean cleaning solution and store it in a safe place.

Front cover

Exhaust cap

Wiper

Exhaust cap

Wiper

On the white side

On the color side

Nozzle guard

Suction
cap

Suction cap

Locations to be
cleaned with
clean stick T

Locations to be
cleaned with
clean stick R

Содержание GTX pro





































































































































































































































































































































































Результаты поиска

Содержание GTX pro

Отзывы:

Brother GTX pro, Инструкция по эксплуатации, Страница: 175 / 356

Результаты поиска

Содержание GTX pro

Отзывы: