Brother GTX pro Скачать руководство пользователя страница 207

Страница: 207 / 356

207

Precautions to keep good printing quality/use printer over the long term

7-2-5. Replacing the platen sheet

When the platen sheet gets soiled, replace it with a new one.

(1)

Remove the platen from the main unit of the printer.

☞

"6-4-1. Replacing the currently used platen with another one >>P.134"

(2)

Peel the platen sheet off the platen.
<TIPS>



When it is hard to peel the platen sheet off, warm it using a hair dryer or the like and peel it off.

X0064

(3)

Wipe the surface of the platen with a clean cloth moistened with a mild detergent which is diluted with water, then

wipe the platen clean with a dry and soft clean cloth.

(4)

Mount the platen in the main unit of the printer.

☞

"6-4-1. Replacing the currently used platen with another one >>P.134"

(5)

Peel the release paper (small in size) off a new platen sheet.

X0157

Platen sheet

Platen

Platen sheet

Release paper (small)

Содержание GTX pro





































































































































































































































































































































































Результаты поиска

Содержание GTX pro

Отзывы:

Brother GTX pro, Инструкция по эксплуатации, Страница: 207 / 356

Результаты поиска

Содержание GTX pro

Отзывы: