Brother GTX pro Скачать руководство пользователя страница 198

Страница: 198 / 356

198

Precautions to keep good printing quality/use printer over the long term

(6)

Mount a new fan filter to the frame of filter case.
<IMPORTANT>



Mount the fan filter properly in correct position in such a way that its coarse mesh surface faces toward the inner area of
printer.

X0062

(7)

Mount the assembled fan filter in the main unit of printer.

(8)

Turn on the power.
<NOTE>



Dispose of any waste resulting from the replacement in accordance with applicable laws and ordinances.

<TIPS>



Then, a head cleaning will be performed to prevent any ink from drying up.

Fan filter

Coarse mesh surface

Filter case

Toward the fan

Toward the inner area of printer

Fine-meshed surface

Содержание GTX pro





































































































































































































































































































































































Результаты поиска

Содержание GTX pro

Отзывы:

Brother GTX pro, Инструкция по эксплуатации, Страница: 198 / 356

Результаты поиска

Содержание GTX pro

Отзывы: