Brother GTX pro Скачать руководство пользователя страница 279

Страница: 279 / 356

279

Troubleshooting

(8)

Remove the resin cover which is placed on the top of the carriage board and remove the flat cable.

X0400

(9)

Unlock the print head, and remove the print head.



When removing the print head in position, be careful not to drip the ink on the carriage plate. If the ink is dripping, wipe off
the dripping ink.

②

①

X0401

(10)

Release the lock by pulling (a) part toward yourself, and take out the new print head from its case.



When removing the print head, be careful not to touch the nozzle surface at the bottom of the head. Otherwise it may cause
poor printing.

<TIPS>



Sometimes, you may find it hard to remove the print head when you try to open the lock of (a) part. If it is hard, use both
hands to remove it.

X0069

Lock

Print head

Flat cable

Resin cover

Case

Print head

(a) part

Содержание GTX pro





































































































































































































































































































































































Результаты поиска

Содержание GTX pro

Отзывы:

Brother GTX pro, Инструкция по эксплуатации, Страница: 279 / 356

Результаты поиска

Содержание GTX pro

Отзывы: