Brother GTX pro Скачать руководство пользователя страница 308 | Manualshive

Страница: 308 / 356

Brother GTX pro Скачать руководство пользователя страница 308

308

Troubleshooting

9-2-8. Re-install the ink

Ink should be re-installed when an entrance of air into the print head or tube prevents proper ink-jet operation and
remedial measure cannot improve the condition.

(1)

While the printer is in standby mode, press

on the operation panel to bring the menu screen into view.

(2)

Press

, select [Maintenance] > [Initial Ink Installation], and press

.

(3)

Press

to select one of the options; [All Colors], [All Whites], or [All Print Heads], and press

.

(4)

According to the message displayed on the operation panel, press

.

Initial ink installation will be operated.

<TIPS>



Estimated time to finish is 30 minutes for [All Whites] and 15 minutes for [All Colors], which, however, may fluctuate
depending on the temperature environment and printer status. After the procedures are completed, the current screen will
go back to the standby mode screen.

«
...
306
307
308
309
310
...
»

Содержание GTX pro





































































































































































































































































































































































Отзывы:

Нет отзывов