Brother GTX pro Скачать руководство пользователя страница 125

Страница: 125 / 356

125

Basic printing procedures

(3)

Orient the pour spout of

faucet

in the position as shown in the figure below.

X0081

(4)

Lean the entire shipping carton of pretreatment toward a container for dilution to pour the agent into the container,

and dilute it with pure water.



Use with the dilution rate of x3 (Pretreatment:Pure water=1:2) (Volume ratio).



Close the cap of the container for dilution, and shake it sufficiently to provide equal concentration.

X0082

(5)

To provide safekeeping for the pretreatment, close the

faucet

, place the pretreatment with the

faucet

part facing

upward, and store the entire carton in a safe place.

Pretreatment

Faucet

Pretreatment

Pure water

Container for dilution

Содержание GTX pro





































































































































































































































































































































































Результаты поиска

Содержание GTX pro

Отзывы:

Brother GTX pro, Инструкция по эксплуатации, Страница: 125 / 356

Результаты поиска

Содержание GTX pro

Отзывы: