Brother GTX pro Скачать руководство пользователя страница 301 | Manualshive

Страница: 301 / 356

Brother GTX pro Скачать руководство пользователя страница 301

301

Troubleshooting

(13)

Insert the flat cable into the core and connect it to the carriage board.

(14)

Fit the claw by pushing the core until it clicks into place.

Leave a slack to avoid interference between the flat cable and the resin cover.

X0413

(15)

Place the resin cover back onto the carriage board, and engage the two latches properly.

Tuck the extra flat cable as shown in the illustration.

X0414

(16)

Remove every cap from each tube, and connect the tubes to the print head.

<IMPORTANT>



To prevent the tubes from being entangled with each other, connect the innermost tube to the print head first, and make the
connection of the rest of the tubes.



Check the stamp on the print head and connect them taking care not to confuse their positions. Incorrectly connecting them
may cause the ink to leak during the circulation.

Flat cable

Resin cover

Latch

Core

«
...
299
300
301
302
303
...
»

Содержание GTX pro





































































































































































































































































































































































Отзывы:

Нет отзывов