Brother GTX pro Скачать руководство пользователя страница 276

Страница: 276 / 356

276

Troubleshooting

(10)

Rotate the nut of the tube on the cartridge side to remove the old filter.

X0438

(11)

Attach the cartridge side tube to a new filter and fasten the nut.



Make sure to install the filter with the stamped side facing the cartridge side tube.

X0335

(12)

Remove the waste cloth from under the filter.

(13)

Close the front cover, turn on the power.

<NOTE>



Dispose of any waste resulting from the replacement in accordance with applicable laws and ordinances.

(14)

Perform the [Filter exchange after ink Load] operation by following the on-screen instructions.

<TIPS>



When replacing multiple filters, go back to the beginning of the procedure to start replacing the next filter.



After the procedures are completed, the current screen will go back to the standby mode screen.

Old filter

Stamped side

New filter

Nut

Cartridge side tube

Nut

New filter

Содержание GTX pro





































































































































































































































































































































































Результаты поиска

Содержание GTX pro

Отзывы:

Brother GTX pro, Инструкция по эксплуатации, Страница: 276 / 356

Результаты поиска

Содержание GTX pro

Отзывы: