Brother GTX pro Скачать руководство пользователя страница 319

Страница: 319 / 356

319

Error message

Error code

Error message

Description

Remedy

Reference

2201

[Maintenance Pouch
Set Magenta]

Although an ink pouch
is needed, a
maintenance solution
pouch is set to the
magenta cartridge.

Set an ink pouch to the magenta
cartridge.

2202

[Maintenance Pouch
Set Cyan]

Although an ink pouch
is needed, a
maintenance solution
pouch is set to the
cyan cartridge.

Set an ink pouch to the cyan
cartridge.

2203

[Maintenance Pouch
Set Yellow]

Although an ink pouch
is needed, a
maintenance solution
pouch is set to the
yellow cartridge.

Set an ink pouch to the yellow
cartridge.

2204

[Maintenance Pouch
Set White12]

Although an ink pouch
is needed, a
maintenance solution
pouch is set to the
white 12 cartridge.

Set the ink pouch to the white 12
cartridge.

2205

[Maintenance Pouch
Set White34]

Although an ink pouch
is needed, a
maintenance solution
pouch is set to the
white 34 cartridge.

Set the ink pouch to the white 34
cartridge.

2214

[Ink Pouch Set
White12]

Although a
maintenance solution
pouch is needed, an
ink pouch is set to the
white 12 cartridge.

Set the maintenance solution
pouch to the white 12 cartridge.

2215

[Ink Pouch Set
White34]

Although a
maintenance solution
pouch is needed, an
ink pouch is set to the
white 34 cartridge.

Set the maintenance solution
pouch to the white 34 cartridge.

2300

[Special operation
mode]

Under the operation
by the service man

If the problem still persists even
after restarting the printer, please
contact your dealer.

2310

[Perform test printing
and check the
ejection from the
head]

Since the parts have
been replaced, you
have to perform test
printing and check the
ejection from the
head.

Perform test printing following the
on-screen instructions.

Содержание GTX pro





































































































































































































































































































































































Результаты поиска

Содержание GTX pro

Отзывы:

Brother GTX pro, Инструкция по эксплуатации, Страница: 319 / 356

Результаты поиска

Содержание GTX pro

Отзывы: