Brother GTX pro Скачать руководство пользователя страница 274 | Manualshive

Страница: 274 / 356

Brother GTX pro Скачать руководство пользователя страница 274

274

Troubleshooting

9-2-5. Replacing the color filter

If a number of non-firing color head nozzles is observed after printing, the filter should be replaced.
<IMPORTANT>



When replacing multiple filters, filters for individual colors should be replaced one by one. Replace the filter for the first color and
install ink, then replace the next filter. Removing multiple filters at the same time might damage the print head.

<TIPS>



Ink installation should be performed after replacing the filters. If the ink level is low, make a new ink pouch available for use.

(1)

Prepare the supplied gloves and optional filter.

(2)

From the menu, select [Maintenance] > [Exchange Filter], and press

.

(3)

From [Black], [Yellow], [Cyan], and [Magenta] select non-firing color and press

.

<TIPS>



Pressing

causes the platen to start moving. Do not put anything around the platen.

(4)

Follow the on-screen message and turn off the power.

(5)

Open the front cover.

X0331

(6)

Lay a waste cloth under the filter to be replaced.

<TIPS>



Non-fuzzy, clean cloth should be used.

X0396

Front cover

Filter

Color print head

Waste cloth

Filter

«
...
272
273
274
275
276
...
»

Содержание GTX pro





































































































































































































































































































































































Отзывы:

Нет отзывов