Brother GTX pro Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 356

Brother GTX pro Скачать руководство пользователя страница 133

133

Basic printing procedures

(1)

Place the silicone foam, T-shirt and peel-off sheet in position under the heat press first, and fixate the pretreatment

properly.

<TIPS>



Water droplets are generated around the heat press to evaporate water content of the pretreatment by the heat of heat
press. Keep your working space clean so that the surface to be coated with the agent will not get wet.



A peel-off sheet should be used if needed, depending on the heat press you use.

X0096

(2)

Remove the T-shirt from the heat press so that the steamy heat will escape from it.

X0097

Water droplets

Heat press

Peel-off sheet

T-shirt

Heat press

T-shirt

Silicone foam

«
...
131
132
133
134
135
...
»

Содержание GTX pro





































































































































































































































































































































































Отзывы:

Нет отзывов