Brother GTX pro Скачать руководство пользователя страница 212

Страница: 212 / 356

212

Precautions to keep good printing quality/use printer over the long term

7-3-2. Reusing White Ink

Perform the following operations when you restart printing with the white ink after activating the white ink pause mode.

(1)

From the menu, select [Maintenance] > [White Ink Pause Mode] > [Disable].

(2)

Check the waste ink tank level and take a necessary measure for it, if any, then press

(3)

Remove the maintenance solution cartridge from the printer.



The bottom of the cartridge may be soiled with ink. Clean the printer on a regular basis.

W12

W34

X0333

(4)

Open the cartridge's lid.



When opening the lid, be sure not to touch portion (a). Otherwise, it could be damaged.



Place the entire cartridge on a flat surface, push the latches on the bottom surface of the cartridge downward and open the
lid.

(a)

X0042

Maintenance solution cartridge

Lid

Cartridge

Latch

Lid

Содержание GTX pro





































































































































































































































































































































































Результаты поиска

Содержание GTX pro

Отзывы:

Brother GTX pro, Инструкция по эксплуатации, Страница: 212 / 356

Результаты поиска

Содержание GTX pro

Отзывы: