Brother GTX pro Скачать руководство пользователя страница 167 | Manualshive

Страница: 167 / 356

Brother GTX pro Скачать руководство пользователя страница 167

167

Basic printing procedures

Ink fixation by means of heat press

(1)

Place the silicone foam, T-shirt and peel-off sheet in position under the heat press first, and fixate the ink properly.

<TIPS>



For the guidelines on fixation conditions of ink

☞

"6-10. Fixation of ink >>P.166".



For details, refer to the instruction manual of your heat press.



There is a tendency to bring the print result to an almost matte finish if a silicone-coated paper is used as a peel-off sheet or
to an almost bright finish if a fluororesin sheet is used as the same at the ink fixation stage. Selectively use either of them
according to your desired finish.

X0115

Ink fixation by means of conveyor-type oven

(1)

Fixate inks onto a T-shirt by means of the conveyor-type oven.

<TIPS>



For the guidelines on fixation conditions of ink

☞

"6-10. Fixation of ink >>P.166".



For the conveyor-type oven, identify the oven's internal temperature, and check up on actual ink fixation result.



For details, refer to the instruction manual of your conveyor-type oven.

X0116

Heat press

Peel-off sheet

T-shirt

T-shirt

Conveyor-type oven

out

in

Silicone foam

«
...
165
166
167
168
169
...
»

Содержание GTX pro





































































































































































































































































































































































Отзывы:

Нет отзывов