manualshive.com logo in svg

ARTERY AT32F435 Series, Справочное руководство

Поделиться
Скачать
ARTERY AT32F435 Series Скачать руководство пользователя страница 635

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 635 

 

Rev 2.03

 

messages relevant to slave. 

Bit 14 

ETSFEM 

0x0 

rw 

Enable Timestamp Snapshot For Event Messages 
When this bit is set, it enables time stamp snapshots for 
event messages only (SYNC, Delay_Req, Pdelay_Req, or 
Pdelay_Resp).  When  this  bit  is  cleared,  time  stamp 
snapshots  are  applicable  to  all  the  messages  except 
Announce, Management and Signaling. 

Bit 13 

EPPFSIP4U 

0x1 

rw 

Enable Processing of PTP Frames Sent over IPv4-UDP 
When this bit is set, the MAC receiver processes the PTP 
encapsulated in UDP over IPv4 packet. When this bit is 
cleared, the MAC ignores the PTP transferred over UDP-
IPv4 packet. This bit is set by default.   

Bit 12 

EPPFSIP6U 

0x0 

rw 

Enable Processing of PTP Frames Sent over IPv6-UDP 
When this bit is set, the MAC receiver processes the PTP 
encapsulated in UDP over IPv6 packet. When this bit is 
cleared,  the  MAC  ignores  the  PTP  sent  over  UDP-IPv6 
packet. 

Bit 11 

EPPEF 

0x0 

rw 

Enable Processing of PTP over EMAC Frames 
When this bit is set, the MAC receiver processes the PTP 
that is directly encapsulated in the Ethernet frames. When 
this bit is cleared, the MAC ignores the PTP over EMAC 
frames. 

Bit 10 

EPPV2F 

0x0 

rw 

Enable PTP packet Processing for Version 2 Format 
When this bit is set, it enables PTP packet processing in 
the format of 1588 V2. Otherwise, 1588 V1 format is used 
for  PTP  packet  processing.  Refer  to 

PTP  process  and 

control

 on page 155 for more details on IEEE 1588 V1 and 

V2. 

Bit 9 

TDBRC 

0x0 

rw 

Timestamp Digital or Binary Rollover Control 
When this bit is set, time stamp low register starts rolling 
after the 0x3B9A_C9FF value (1 ns precision), and    the 
time stamp (high) second is incremented. When this bit is 
cleared,  the  rollover  value  of  the  subsecond  register  is 
0x7FFF_FFFF.  The  subsecond  increment  must  be 
configured  according  to  PTP  reference  clock  frequency 
and the value of this bit. 

Bit 8 

ETAF 

0x0 

rw 

Enable Timestamp for All Frames 
When this bit is set, it enables time stamp snapshot for all 
received frames on the MAC. 

Bit 7: 6 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 5 

ARU 

0x0 

rw 

Addend Register Update 
When this bit is set, the Ethernet PTP time stamp addend 
register’s contents are updated on the PTP block for fine 
correction.  This  bit  is  cleared  when  the  update  is 
completed. This register bit must be read as 0 before being 
set. 

Bit 4 

TITE 

0x0 

rw 

Timestamp Interrupt Trigger Enable 
When this bit is set, a time stamp interrupt is enabled if the 
system time becomes greater than the value written in the 
target time register. This bit is cleared when the time stamp 
trigger interrupt is generated. 

Bit 3 

TU 

0x0 

rw 

Timestamp Update 
When this bit is set, the system time is updated (added or 
subtracted from) with the value programmed in the system 
time second update register and system time nanosecond 
update register.   
This bit must be read as 0 before being updated. This bit 
is cleared after the hardware update is completed. Time 
stamp high word register (if enabled) is not updated. 

Bit 2 

TI 

0x0 

rw 

Timestamp Initialize 
When  this  bit  is  set,  the  system  time  is  initialized 
(overwritten)  with  the  value specified  in  the  system time 
second  update  register  and  system  time  nanosecond 
update register. 

Содержание AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды