manualshive.com logo in svg

ARTERY AT32F435 Series, Справочное руководство

Поделиться
Скачать
ARTERY AT32F435 Series Скачать руководство пользователя страница 488

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 488 

 

Rev 2.03

 

21.6.5.11  OTGFS device control OUT endpoint 0 control register 

(OTGFS_DOEPCTL0)   

This  section  describes  the  control  OUT  endpoint  0  control  register.  Non-zero  control  endpoints  use 
registers for endpoints 1-7. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31 

EPTENA 

0x0 

rw1s 

Endpoint enable 
The application sets this bit to start transmitting data on 
endpoint 0.The controller clears this bit before setting any 
one of the following interrupts on this endpoint: 

– 

SETUP stage done 

– 

Endpoint disabled 

– 

Transfer completed 

Bit 30 

EPTDIS 

0x0 

ro 

Endpoint disable 
The application cannot disable control OUT endpoint 0. 

Bit 29: 28  Reserved 

0x0 

resd 

Kept at its default value. 

Bit 27 

SNAK 

0x0 

wo 

Set NAK 
A write to this bit sets the NAK bit for this  endpoint. The 
application can use this bit to control the transmission of 
NAK handshakes on an endpoint. The controller sets this 
bit  on  a  transfer  completed  interrupt  or  when  a  SETUP 
data packet is received. 

Bit 26 

CNAK 

0x0 

wo 

Clear NAK 
A write to this bit clears the NAK for the endpoint. 

Bit 25: 22  Reserved 

0x0 

resd 

Kept at its default value. 

Bit 21 

STALL 

0x0 

rw1s 

STALL handshake 
The application sets this bit and the controller clears this 
bit when a SETUP token is received for this endpoint. If a 
NAK bit, global non-periodic OIT NAK bit is set along with 
this bit, the STALL bit has priority. The controller always 
responds to SETUP data packets, regardless of whether 
this bit is set or not. 

Bit 20 

SNP 

0x0 

rw 

Snoop mode 
This  bit  configures  the  endpoint  to  Snoop  mode.  In  this 
mode,  the  controller  does  not  check  the  correctness  of 
OUT  packets  before  transmitting  OUT  packets  to  the 
application memory. 

Bit 19: 18  EPTYPE 

0x0 

ro 

Endpoint type 
Hardware sets this bit to 0 to control endpoint type. 

Bit 17 

NAKSTS 

0x0 

ro 

NAK status 
Indicates the followings: 
0: The controller is sending non-NAK handshakes based 
on the FIFO status 
1: The controller is sending NAK handshakes 

– 

When this bit is set (either by the application or the 
controller), the controller stops receiving any data on an 
OUT endpoint, even if there is space in the receive FIFO. 
The  controller  always  responds  to  SETUP  data  packets 
with an ACK handshake, regardless of whether this bit is 
set or not. 

Bit 16 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 15 

USBACEPT 

0x1 

ro 

USB active endpoint 
This bit is always set to 1, indicating that a control endpoint 
0 is always active in all configurations and interfaces. 

Bit 14: 2 

Reserved 

0x0000 

resd 

Kept at its default value. 

Bit 1: 0 

MPS 

0x0 

ro 

Maximum packet size 
The maximum packet size of the control OUT endpoint 0 
is the same as that of the control IN endpoint 0. 
00: 64 bytes 
01: 32 bytes 
10: 16 bytes 
11: 8 bytes 

Содержание AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды