manualshive.com logo in svg

ARTERY AT32F435 Series, Справочное руководство

Поделиться
Скачать
ARTERY AT32F435 Series Скачать руководство пользователя страница 499

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 499 

 

Rev 2.03

 

remains 0. The RSLOST bit is immediately cleared after 
the CALON bit is cleared or when the RSLOST is written 
with  0.  Reference  signal  detection  occurs  only  when 
CALON=1.

 

Bit 0 

CALRDY 

0x0 

ro 

Internal high-speed clock calibration ready 
0: Internal 8MHz oscillator calibration is not ready 
1: Internal 8MHz oscillator calibration is ready 
Note: This bit is set by hardware to indicate that internal 
8MHz  oscillator  has  been  calibrated  to  the  frequency 
closest  to  8MHz.  The  CALRDY  is  immediately  cleared 
after  the  CALON  bit  is  cleared  or  when  the  CALRDY  is 
written with 0.

 

22.6.3  Control register 1 (ACC_CTRL1) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 12  Reserved 

0x00000 

resd 

Forced by hardware to 0 

Bit 11: 8 

STEP 

0x1 

rw 

Calibrated step 
This field defines the value after each calibration. 
Note: It is recommended to set the step bit in order to get 
a more accurate calibration result. While ENTRIM=0, only 
the HICKCAL is calibrated. If the step is incremented or 
decremented by one, the HICKCAL will be incremented or 
decremented by one accordingly, and the HICK frequency 
will increase or decrease by 40KHz (design value). This is 
a positive relationship. 
While ENTRIM=1, only the HICKTRIM is calibrated. If the 
step  is  incremented  or  decremented  by  one,  the 
HICKTRIM  will  be  incremented  or  decremented  by  one 
accordingly,  and  the  HICK  frequency  will  increase  or 
decrease  by  20KHz  (design  value).  This  is  a  positive 
relationship. 

Bit 7: 6 

Reserved 

0x0 

rw 

Forced by hardware to 0 

Bit 5 

CALRDYIEN 

0x0 

rw 

CALRDY interrupt enable 
This bit is set or cleared by software. 
0: Interrupt generation disabled 
1:  ACC  interrupt  is  generated  when  CALRDY=1  in  the 
ACC_STS register 

Bit 4 

EIEN 

0x0 

rw 

RSLOST error interrupt enable 
This bit is set or cleared by software. 
0: Interrupt generation disabled 
1:  ACC  interrupt  is  generated  when  RSLOST=1  in  the 
ACC_STS register

 

Bit 3: 2 

Reserved 

0x0 

rw 

Forced by hardware to 0 

Bit 1 

ENTRIM 

0x0 

rw 

Enable trim 
This bit is set or cleared by software. 
0: HICKCAL is calibrated. 
1: HICKTRIM is calibrated. 
Note: It is recommended to set ENTRIM=1 in order to get 
higher calibration accuracy. 

Bit 0 

CALON 

0x0 

rw 

Calibration on 
This bit is set or cleared by software. 
0: Calibration disabled 
1: Calibration enabled, and starts searching for a pulse on 

the USB_SOF. 

Note: This module cannot be used without the USB_SOF 
reference  signal.  If  there  are  no  requirements  on  the 
accuracy  of  the  HICK clock,  it  is  unnecessary  to enable 
this module. 

Содержание AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды