Arctic Cat 425 2011 страница 47 Скачать руководство пользователя | Manualshive

Страница: 47 / 122

background image

46

13. Connect the coolant hoses to the water pump and

secure with the hose clamps. Tighten securely.

Right-Side Components



NOTE: For efficiency, it is preferable to remove and

disassemble only those components which need to
be addressed and to service only those components.
The technician should use discretion and sound
judgment.



NOTE: The engine/transmission does not have to

be removed from the frame for this procedure.

Removing Right-Side

Components

A. V-Belt Cover
B. Driven Pulley
C. Clutch Cover

1. If the engine is still in the frame, remove the cap

screw securing the brake pedal to the pivot shaft.

Account for a flat washer.

KC149A

2. Remove the cap screws securing the V-belt cover to

the clutch cover; then slide the brake pedal outward

and remove the V-belt cover. Account for two align-

ment pins and a gasket.

KC142A

3. Mark the movable drive face and the fixed drive face

for installing purposes; then remove the nut holding

the movable drive face onto the crankshaft.

MD1033

4. Remove the movable drive face and spacer. Account

for the movable drive face rollers and outer drive

face cover.

MD1035

MD1034



AT THIS POINT

To service center crankcase components only, proceed
to Removing Right-Side Components.



AT THIS POINT

To service any one specific component, only limited dis-
assembly of components may be necessary. Note the
AT THIS POINT information in each sub-section.

Manual

Table of Contents

«
...
45
46
47
48
49
...
»

Содержание 425 2011



























































































































Отзывы:

Нет отзывов

Похожие инструкции для 425 2011

Бренд: Taylor-Dunn Страницы: 254

Бренд: Can-Am Страницы: 58

Бренд: AC Air Technology Страницы: 49

Бренд: Dcm Страницы: 14

Twister UM250IIR

Бренд: Hammerhead Страницы: 67

Бренд: Fort Страницы: 88

Бренд: FarmTek Страницы: 5

Engine Drive AY20

Бренд: Miller Electric Страницы: 2

Бренд: Federal Signal Corporation Страницы: 140

Бренд: Baja Страницы: 180

Sasquatch 1000W

Бренд: Daymak Страницы: 24

Бренд: Yamaha Страницы: 54

Бренд: Yamaha Страницы: 180

Бренд: Arctic Cat Страницы: 92

Бренд: Range Road Страницы: 6

Бренд: Baja motorsports Страницы: 7

Бренд: Yamaha Страницы: 188

Бренд: Sauber Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды