Arctic Cat 425 2011 Скачать руководство пользователя

Страница: 105 / 122

104

PR715

7. Using an appropriate seal removal tool, carefully

remove the seals from the brake caliper housing; then

remove four O-rings from the brake caliper housing

noting the location of the different sized O-rings. Dis-

card all seals, O-rings, and crush washers.

CLEANING AND INSPECTING

1. Clean all caliper components (except the brake pads)

with DOT 4 brake fluid. Do not wipe dry.

2. Inspect the brake pads for damage and excessive

wear.



NOTE: For measuring brake pads, see Periodic

Maintenance.

3. Inspect the brake caliper housings for scoring in the

piston bores, chipped seal ring grooves, or signs of

corrosion or discoloration.

4. Inspect the piston surface for scoring, discoloration,

or evidence of binding or galling.

5. Inspect the caliper holder for wear or bending.

ASSEMBLING/INSTALLING

1. Install new seals into the brake caliper housing and

apply a liberal amount of DOT 4 brake fluid to the

cylinder bore of the housing, seals, and brake piston.

PR715

PR717A

2. Press the piston into the caliper housing using hand

pressure only. Completely seat the piston; then wipe

off any excessive brake fluid.

PR711A

PR712

3. Apply high-temperature silicone grease (supplied

with the O-ring kit) to the inside of the caliper holder

bores and O-rings; then install the four O-rings into

the caliper.

PR719C

4. Install the caliper onto the caliper holder making sure

the caliper and holder are correctly oriented.

! WARNING

Make sure to hold the towel firmly in place or the piston
could be ejected from the housing causing injury.

CAUTION

Make sure the seals are properly in place and did not
twist or roll during installation.

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды