Arctic Cat 425 2011 Скачать руководство пользователя

Страница: 65 / 122

Fuel/Lubrication/Cooling



NOTE: Arctic Cat recommends the use of new gas-

kets, lock nuts, and seals and lubricating all internal
components when servicing the engine/transmission.

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when performing service procedures in this section.

Refer to the current Special Tools Catalog for the appro-

priate tool description.



NOTE: Special tools are available from the Arctic

Cat Service Parts Department.

Electronic Fuel Injection

TROUBLESHOOTING

1. Verify that the electric fuel pump is operating by lis-

tening for a “whirring” sound for several seconds after

the ignition switch is turned to the ON position. If no

sound can be heard, see Electric Fuel Pump/Fuel

Level Sensor in this section.

2. Check for a flashing EFI icon on the LCD. If EFI is

flashing, see ECU Error Codes in the Electrical Sys-

tem section.

3. Make sure there is sufficient, clean gas in the gas

tank.

4. Verify that the battery is sufficiently charged to crank

the engine over at normal speed.

5. Check the air filter housing and air filter for contam-

ination. Clean or replace as necessary (see Periodic

Maintenance section).

Throttle Body

REMOVING

1. Remove the heat shields and seat.

2. Disconnect the negative battery cable; then remove

the gas tank (see Gas Tank in this section).

3. Loosen the clamp securing the intake boot to the throttle

body; then loosen the clamp securing the intake boot to

the intake housing and slide the intake housing rearward.

FI691A

4. Disconnect the MAP/IAT sensor connector, ISC con-

nector, and TPS connector; then loosen the clamp

securing the throttle body to the intake manifold boot

and slide the throttle body out.

FI528A

5. Remove the throttle arm cover and loosen the throttle

cable jam nut; then disconnect the throttle cable and

remove the throttle body.

INSTALLING

1. Connect the throttle cable to the throttle arm; then

install the throttle cable housing in the throttle body

and tighten the jam nut. Install the throttle arm cover

and secure with two machine screws.

2. Place the throttle body into the intake manifold boot

and tighten the boot clamp securely.

3. Place the intake housing into the boots and tighten

the boot clamps securely.

4. Install the gas tank; then the heat shields and seat.

Throttle Cable Free-Play

To adjust throttle cable free-play, see Periodic Maintenance.

Description

p/n

Oil Pressure Test Kit

0644-495

Tachometer

0644-275

! WARNING

Whenever any maintenance or inspection is performed
on the fuel system during which there may be fuel leak-
age, there should be no welding, smoking, open flames,
etc., in the area.

! WARNING

Gasoline may be under pressure. Place an absorbent
towel under the connector to absorb any gasoline spray
when disconnecting.

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды