Arctic Cat 425 2011 Скачать руководство пользователя | Manualshive

Страница: 104 / 122

background image

103

2. Drain the brake fluid from the caliper, hose, and mas-

ter cylinder through the bleed screw by pumping the

brake lever/pedal.

PR235



NOTE: Whenever brake components are removed,

disassembled, or repaired where brake fluid is
exposed to air, drain all fluid and replace with new
DOT 4 brake fluid from an unopened container. Brake
fluid readily absorbs moisture from the air signifi-
cantly lowering the boiling point. This increases the
chance of vapor lock reducing braking power and
increasing stopping distance.

3. Remove the brake hose from the caliper and close

the bleed screw; then remove the caliper.

4. Compress the caliper holder against the caliper

(opposite the O-ring side) and remove the outer

brake pad; then remove the inner brake pad.



NOTE: If brake pads are to be returned to service,

do not allow brake fluid to contaminate them.

PR237A

PR238

5. Remove the caliper holder from the caliper and dis-

card the O-ring.

PR239B



NOTE: The O-ring is used for shipping purposes

and provides no function in operation.

6. Cover the piston end of the housing with a shop

towel; then keeping fingers clear of piston travel,

apply compressed air to the fluid port to blow the

piston free of the housing. Account for two seal

rings in the housing.

PR713A

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

! WARNING

Never let brake fluid contact the eyes. Damage to the
eyes will occur. Always wear appropriate protective
safety goggles and latex gloves when handling brake
fluid.

CAUTION

Brake fluid is highly corrosive. Do not spill brake fluid
on any surface of the ATV and do not reuse brake fluid.

Manual

Table of Contents

«
...
102
103
104
105
106
...
»

Содержание 425 2011



























































































































Отзывы:

Нет отзывов

Похожие инструкции для 425 2011

WOLVERINE YFM45FXV

Бренд: Yamaha Страницы: 34

BLASTER YFS200S

Бренд: Yamaha Страницы: 46

Бренд: Monowalker Страницы: 27

Бренд: Algema Страницы: 108

Бренд: Coleman Powersports Страницы: 46

Бренд: Komatsu Страницы: 4

Tanks2Go 1200lt Mobile Fuel Tank Trailer

Бренд: Fuelfix Страницы: 17

Off-Roader 36EL

Бренд: Texas Страницы: 27

Бренд: Xtreme Power Страницы: 10

Бренд: Aero Страницы: 12

Бренд: Humbaur Страницы: 4

Бренд: KEEWAY Страницы: 97

SmarTrax John Deere 8X60 Series

Бренд: Raven Страницы: 48

2012 TERRAIN 250

Бренд: Ezgo Страницы: 76

Бренд: Toro Страницы: 52

Бренд: Toro Страницы: 55

Бренд: Toro Страницы: 44

Бренд: Herculano Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды