Arctic Cat 425 2011 страница 93 Скачать руководство пользователя

Страница: 93 / 122

AF994

2. Install the input shaft seal making sure it is flush with

the edge of the housing.

3. Lubricate the input shaft splines with High-Perfor-

mance #2 Molybdenum Disulphide Grease.



NOTE: Any time drive splines are separated, clean

all splines with parts-cleaning solvent and dry with
compressed air; then lubricate with recommended
grease.

KX221

KX222

4. Install the input shaft into the housing; then install

the front boot and secure with an appropriate boot

clamp and the rear boot with an appropriate boot

clamp.

CD112

5. Using a new O-ring lubricated with grease, install

the front drive actuator and secure with the cap

screws.

6. Place the pinion housing with new gasket onto the

gear case housing; then secure with the existing cap

screws. Tighten to 18 ft-lb.

CD103

Disassembling Pinion Gear



NOTE: This procedure can be performed on a rear

gear case.

1. Remove the cap screws securing the pinion housing;

then remove the housing and account for a gasket.

Account for the coupler, fork, and spring.

KX209

2. Remove the cap screws securing the gear case cover.

Account for and make note of the ID tag location for

assembling purposes.

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды