manualshive.com logo in svg

Arctic Cat 425 2011, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat 425 2011 Скачать руководство пользователя страница 13

12

AL611D

2. Turn the adjuster until the throttle cable has proper

free-play of 3-6 mm (1/8-1/4 in.) at the lever.

ATV-0047

3. Tighten the jam nut against the throttle cable adjuster

securely; then slide the rubber boot over the adjuster.

Adjusting Engine RPM 

(Idle)

NOTE: Engine idle RPM is not adjustable on  this

model.

Engine/Transmission

Oil - Filter

The engine should always be warm when the oil is

changed so the oil will drain easily and completely.

1. Park the ATV on level ground.

2. Remove the seat and left-side engine cover.

3. Remove the oil level stick/filler plug.

KC0051A

4. Remove the drain plug from the bottom of the engine

and drain the oil into a drain pan.

733-441A

5. Remove the oil filter plug from the filter mounting

boss (located on the front side of the transmission

case) and allow the filter to drain completely. Install

the plug and tighten securely.

6. Using the adjustable Oil Filter Wrench and a suitable

wrench, remove the old oil filter. 

NOTE: Clean up any excess oil after removing the

filter.

7. Apply oil to a new filter seal ring and check to make

sure it is positioned correctly; then install the new oil

filter. Tighten securely.

8. Install the engine drain plug and tighten to 20 ft-lb.

Pour the specified amount of the recommended oil in

the filler hole. Install the oil level stick/filler plug.

9. Start the engine (while the ATV is outside on level

ground) and allow it to idle for a few minutes.

10. Turn the engine off and wait approximately one minute. 

11. Remove the oil level stick and wipe it with a clean

cloth; then install the oil level stick into engine case.

NOTE: The oil level stick should be threaded into

the case for checking purposes.

CAUTION

Any oil used in place of the recommended oil could
cause serious engine damage. Do not use oils which
contain graphite or molybdenum additives. These oils
can adversely affect clutch operation. Also, not recom-
mended are racing, vegetable, non-detergent, and cas-
tor-based oils.

Manual

Table of Contents

Содержание 425 2011



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды