Arctic Cat 425 2011 Скачать руководство пользователя

Страница: 77 / 122

RESISTANCE



NOTE: For these tests, the meter selector should be

set to the OHMS position and the primary wire should
be disconnected.

Primary Winding

1. Connect the red tester lead to either terminal; then

connect the black tester lead to the other terminal.

2. The meter reading must be within specification.

Secondary Winding

1. Remove the plug cap from the high tension lead;

then connect the red tester lead to the high tension

lead.

2. Connect the black tester lead to ground.

3. The meter reading must be within specification.



NOTE: If the meter does not show as specified,

replace ignition coil.

Spark Plug Cap

1. Connect the red tester lead to one end of the cap;

then connect the black tester lead to the other end of

the cap.

AR603D

2. The meter reading must be within specification.



NOTE: If the meter does not read as specified,

replace the spark plug cap.

Primary Voltage - ECU

1. Set the meter selector to the DC Voltage position;

then disconnect the two wires from the coil.

2. Connect the red tester lead to the orange wire and the

black tester lead to the blue/white wire.

3. Turn the ignition switch to the ON position. The

meter must show battery voltage.

Speed Sensor

1. Set the meter selector to the DC Voltage position.

2. With appropriate needle adapters on the meter leads,

connect the red tester lead to the voltage lead (V);

then connect the black tester lead to the ground lead

(G).

KC248A

3. Turn the ignition switch to the ON position.

4. The meter must show greater than 5.0 volts.

5. Leave the black tester lead connected; then connect

the red tester lead to the signal lead pin (S).

6. Slowly move the ATV forward or backward; the

meter must show 0 and 6 volts alternately.



NOTE: If the sensor tests are within specifications,

the speedometer must be replaced (see Steer-
ing/Frame/Controls section).

To replace a speed sensor, use the following procedure.

1. Disconnect the three-wire connector from the speed

sensor; then remove the cap screw securing the sen-

sor to the sensor housing.

2. Remove the sensor from the sensor housing account-

ing for an O-ring.

3. Install the new speed sensor into the housing with

new O-ring lightly coated with multi-purpose grease;

then secure the sensor with the cap screw (threads

coated with blue Loctite #242). Tighten securely.

CD071

CAUTION

Always disconnect the battery when performing resis-
tance tests to avoid damaging the multimeter.

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды