Arctic Cat 425 2011 Скачать руководство пользователя

Страница: 69 / 122

AF734D

4. Install the front body panel and rack (see Steer-

ing/Frame/Controls section).

5. Fill the cooling system with the recommended

amount of antifreeze. Check for leakage.

6. Connect the fan wiring to the main wiring harness.

THERMOSTAT
Removing

1. Drain approximately one quart of coolant from the

cooling system.

2. Remove the two cap screws securing the thermostat

housing to the mounting bracket. Remove the ther-

mostat housing cover and account for an O-ring and

a thermostat.

Inspecting



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect the thermostat for corrosion or spring damage.

2. Using the following procedure, inspect the thermo-

stat for proper operation.

A. Suspend the thermostat in a container filled with

water.

B. Heat the water and monitor the temperature with a

thermometer.

C. The thermostat should start to open at 71-86° C

(160-187° F).

D. If the thermostat does not open, it must be

replaced.

3. Inspect all coolant hoses, connections, and clamps

for deterioration, cracks, and wear.



NOTE: All coolant hoses and clamps should be

replaced every four years or 4000 miles.

Installing

1. Place the thermostat and O-ring into the thermostat

housing; then secure the thermostat housing to the

mounting bracket with the two cap screws.

2. Fill the cooling system to the recommended level

with antifreeze. Check for leakage.

WATER PUMP



NOTE: The water pump is a non-serviceable compo-

nent. It must be replaced as an assembly.

Removing

1. Remove the radiator cap; then remove the water

pump drain and drain the coolant.

FI530A

2. Drain the oil from the engine/transmission.

3. Remove the four torx-head cap screws securing the

front and rear fenders to the footrest; then remove the

four cap screws securing the footrest to the frame.

Remove the footrest.

4. Loosen the hose clamps and slide the clamps away

from the hose ends approximately 2 in.; then remove

the hoses from the water pump.

5. Remove the four cap screws securing the water

pump to the engine; then remove the water pump.

FI538A

Installing

1. Secure the water pump to the engine with the four

cap screws tightened to 8 ft-lb.

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды