Arctic Cat 425 2011 Скачать руководство пользователя

Страница: 41 / 122

Removing Left-Side

Components

A. Water Pump
B. Speed Sensor
C. Magneto Cover/Stator Assembly

1. Remove the coolant hose connecting the water pump

to the cylinder; then remove the water pump cover.

FI538

2. Remove the water pump housing assembly noting

the location of the longer cap screw. Account for a

gasket and two alignment pins.

FI539

FI541

3. Remove two cap screws and the oil bolt securing the

oil pressure relief line to the engine. Account for two

crush washers and an O-ring.

FI544

4. Remove the water pump drive gear; then remove the

speed sensor housing assembly. Account for two

alignment pins, a gasket, and two seal washers.

FI543

5. Remove the cap screws securing the magneto cover

to the crankcase. Note the location of the two inter-

nal cap screws and the two longer cap screws.

FI596A

6. Remove the magneto cover and account for two

alignment pins and the gasket.

D. Rotor/Flywheel
E. Starter Clutch/Gear
F. Starter Motor



NOTE: Steps 1-6 in the preceding sub-section must

precede this procedure.

7. Remove the nut securing the rotor/flywheel on the

crankshaft and install the crankshaft protector.

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды